What should I do if I want to restrict access to the network for some devices or children's devices

STEP 1: Log in to the wireless router management page

In the browser address bar, enter: itoolink.net. Press the Enter key, and if there is a login password, enter the router management interface login password and click "Login".

STEP 2:

Follow these steps

1. Enter advanced settings

2. Click on Security Settings

3. Find MAC filtering

STEP 3：

After the restrictions were completed, I found that I couldn't access the internet with my device

The network bandwidth resources are limited, and some terminal devices such as high-speed downloads and video live streaming will occupy a large amount of bandwidth, leading to other computers experiencing phenomena such as "slow internet access, high network cards, and high game ping values with large fluctuations".

The QoS function can limit the maximum uplink and downlink rates of computers, thereby ensuring the rational utilization of the entire network bandwidth resources.

STEP 1: Log in to the router management page

In the browser address bar, enter: itoolink.net. Press the Enter key, and if there is a login password, enter the router management interface login password and click "Login".

STEP 2: Enable QoS function

Find the basic settings as shown in the following figure, locate the QoS switch, and enable it

STEP 3：Set total bandwidth

STEP 4：Add restricted devices

1. Select the 'Add' option from the rule list below.

2. Click on "Magnifier icon" to display the list of currently connected devices.

3. Select the device you want to limit bandwidth on. (The illustrated items are only examples)

4. Specify the upload and download bandwidth size you want to limit.

5. Click the "Add" button on the right side of the rule to add it.

When my computer is connected to my TOTOLINK router and cannot obtain an IP address, I can check if my PC is configured as a static IP by following these steps

STEP 1: 

Right-click the network icon in the lower right corner of the desktop, click to open "Network and internet settings"

STEP 2:

Scroll down, find and click on Network and Sharing Center

STEP 3：

Click on Ethernet

STEP 4：

Point Properties

STEP 5：

Find and double-click Internet Protocol 4 (TCP/IPv4)

STEP 6：

STEP 7：

The page automatically jumps back to Ethernet and click OK

This article introduces a wireless router compatible with TOTOTOLINK APP, using X6000R as an example

STEP 1:

Follow the steps below to connect your router.

STEP 2 :

Connect the mobile phone to the WiFi of TOTOLINK_X6000R, as shown in the figure below

STEP 3 

Launch the Tether App on your phone

If there is no such APP, the Android device can download it through the Google play store,

Apple devices can be downloaded through the IOS store

1. Android device

2. IOS device  

STEP 4 

Select your TOTOLINK wireless router from device list. Then Enter admin for the password and then click LOGIN.

STEP-5: Log in to Quick Setup (Auto jump Quick Setup is only Applicable for the first connection setup)

STEP-6: Quick Setup.

STEP-7: More features: Click Application or Tools.

STEP-8: Binding router, remote management. 

STEP 1:

Connect the line according to the method shown in the figure below.

If you don’t have a PC, you can also use your mobile phone or tablet to connect to the router’  WiFi. The SSID is generally TOTOLINK_model, and the login address is itotolink.net or 192.168.0.1

STEP 2 :

Log in to itotolink.net or 192.168.0.1 through a browser to enter the routing dashboard interface.

PC:

Mobile devices：

STEP 3 :

Through the PC interface as follows：

Through the phone UI as follows：

If you cannot successfully log in according to the above methods, or your account password cannot be logged in normally,

It is recommended that you restore the router to its original factory defaults and then operate again.

Application introduction:

This document describes the characteristics and application scenarios of different modes supported by TOTOLINK CPE, including Client mode, Repeater mode, AP mode and WISP mode.

STEP-1: Client mode

Client mode is used to transfer wireless connection into wired connection. In Client mode, the device serves as a wireless adapter. It receives the wireless signal from root AP or station, and provides wired network for users.

Scenario 1:

Scenario 2:

STEP-2: Repeater mode

Repeater Mode In this mode,you can extend the superior Wi-Fi signal by Repeater setting function under the Wireless column to increase the coverage of the wireless signal.

Scenario 1:

Scenario 2:

STEP-3: AP mode

AP mode connect the superior AP/Router by wire, you can transfer the superior's AP/Router wired signal into wireless signal.

Scenario 1:

Scenario 2:

Scenario 3:

Scenario 4:

STEP-4: WISP Mode

WISP Mode In this mode, all ethernet ports are bridged together and the wireless client will connect to ISP access point. The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN. 

Scenario 1:

FAQ Common problem

Q1: How to reset the CPE to factory default Settings?

Keep the CPE powered on, press the RESET button on CPE or Passive PoE box about 8 seconds, the CPE will restore to factory default settings.

Q2: What Can I do If I forgot the CPE’s Web Login User Name and Password?

In case you changed your CPE’s Login User Name and Password, we suggest you reset your CPE to factory default settings by above operations. Then use the following parameters to login the CPE’s Web interface:

Default IP address: 192.168.1.1

User Name: admin

Password: admin

Application introduction:

After entering the management address of the CPE in the address bar of Chrome browser, the page cannot be displayed after entering the management password, as shown below.

Note: Ensure that the login IP address you typed in the address bar is correct, as well as the login username and password. 

Set up steps

STEP-1: Change browser and clear browser cache

Try changing old version (before 72.0.3626.96) of Chrome browser or try other browser, such as Firefox, Internet Explorer, etc., and clear your browser cache.

Delete cookies on the web browser. Here we take Firefox for example.

Note: In general, the browser enters the management address of the CPE and error pops up. Please use this method first.

STEP-2: Take CP900 as an example

2-1. CP900 default Gateway IP address 192.168.0.254:

Assigned manually IP address 192.168.0.x （“x” range from 2 to 253）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.254.

2-2. Enter 192.168.0.254 into the address bar of your browser. Log in the settings interface.

[Note]: 

The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

Preparation

★ Before downloading files. please confirm the hardware version ofyour device and choose the corresponiding firmware version to uparade. 

★ Wrong firrmware version may damage your device and no warrante.

Set up steps

STEP-1: Guide for Hardware Version

For most TOTOLINK CPE, you can see two bar coded stickers at the front of the device, the character string started with Model No.(for example CP300) and ended with hardware Version (for example V2.0) is the serial number of your device. 

See below:

STEP-2: 

Open browser, enter www.totolink.net Download the required files.

For example, if your hardware yersion is V2.0 , please download V2 version. 

Note: If the hardware version is V1, V1 will be hidden.

STEP-3: 

Unzip the file, correct upgrade file name is suffixed with ”web” or “bin” (except for some special models)

Application introduction: 

Some TOTOLINK products have more than one hardware version, using V1, V2, etc for separation, and generally, each hardware version corresponds to a specifically developed firmware. 

If you want to upgrade your device to the latest firmware, you need to choose the correct firmware version for your device. 

【 CAUTION 】

All content on this website is only applicable to models selling in overseas markets (outside China   mainland, Taiwan and South Korea ),  any model purchased from China mainland,Taiwan or South Korea caused damage by upgrading software on this website is excluded in after-sales service range

For most TOTOLINK products, you can see a bar coded sticker at the front of the device, there is a  character string “VX.Y” (for example, V1.1), See below:  

The number X is the Hardware Version of your device. If the string shows “V1.y”, it means the hardware version is V1.