Application introduction: 

DMZ (Demilitarized Zone) is a network which has fewer default firewall restriction than the LAN does. It allow all the devices connected to the port to be exposed to the Internet for some special-purpose services.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:

The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Enter the Advanced Setup page of the router, Click Firewall->DMZ on the navigation bar on the left.

STEP-4:

Select Enable On/Off bar，You can setup the Host IP address in the box，And then click Apply button.

Note:

When DMZ is enabled, the DMZ host is totally exposed to the internet, which may bring some potential safety hazards. If DMZ is not in use, please disable it in time.

Application introduction: 

DDNS (Dynamic Domain Name System) is useful for your own website, FTP server or other server behind the router.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:

The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Enter the Advanced Setup page of the router, Click Managemet->DDNS on the navigation bar on the left.

STEP-4:

Enter the Service Provider, Domain Name, User Name and Password in the blank space, and then click Apply to apply the modification. 

Application introduction

AP mode,connect the superior AP/Router by wire, you can bridge the superior's AP/Router wired signal into wireless Wi-Fi signals for Wi-Fi devices. Here we take A3000RU for demonstration.

Note: Confirm that your wired network can share the Internet.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3: 

You need to enter the settings page of the router, then follow the steps illustrated.

  ① Set 2.4G network -> ②Set 5G network -> ③Click the Apply button

STEP-4:

Enter the Advanced Setup page of the router, then follow the steps illustrated.

 ① Click Operation Mode> ② Select Bridge Mode-> ③ Click Apply button

STEP-5:

Congratulations! Now all your Wi-Fi enabled devices can connect to the customized wireless network.

Note: 

After the AP mode is set successfully, you cannot log in to the management page. If you need to make changes, please Reset the router.

STEP-1: Difference of 2.4G and 5G Wi-Fi

1-1.The primary difference between the 2.4 GHz and 5GHz wireless frequencies is range as the 2.4GHz frequency is able to reach farther than the 5GHz frequency. This is a result of the basic characteristics that waves attenuate much faster at higher frequencies. So if you are more concerned with the coverage, you should select 2.4GHz rather than 5GHz.

1-2.The second difference is the number of devices on the frequencies. 2.4GHz suffers more interference than 5GHz.

1). The older 11g standard only uses the 2.4GHz frequency, majority of the world is on it. 2.4 GHz has fewer channel options with only three of them non-overlapping, while 5GHz has 23 non-overlapping channels.

2). A lot of other devices are also on the 2.4 GHz frequencies, the biggest offenders are microwaves and cordless phones. These devices add noise to the medium that can further decrease the speed of wireless networks.

In both aspects, choosing to deploy on the 5GHz frequency is the much better option as you have more channels to use to isolate yourself from other networks and there are far fewer interference sources.

But the radar and military frequency is also 5GHz, so 5GHz wireless may also have some interference, and many countries require that wireless devices working on 5GHz should support DFS(Dynamic Frequency Selection) and TPC(Transmitting Power Control).

STEP-2: Summary

3-1. All TOTOLINK dual band routers support 2.4GHz and 5GHz simultaneously；

3-2. 5GHz has a shorter range than 2.4GHz;

3-2. 5GHz radio band that offers high-speed wireless connection that could with less interference in compare to 2.4G WiFi network.

Application introduction: New version of firmware will be released to improve the various efficiency or to fix some bugs. Following the steps show below so as to realize upgrading.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Click Management/System->upgrade firmware. Choose the firmware file for upgrading.Then click the Upgrade button. Then wait for few minutes, the router restart automatically.

Notice: 

1.DO NOT power off the device or close the browser window during the upload because it may crash the system.

2.The correct upgrade firmware is a file suffixed with the Web.

Application introduction: Solution about how to configure QoS on TOTOLINK products.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Please go to Qos ->Qos page, and check which you have selected. Select Enable, then Input Total Uplink Bandwidth and Total Downlink Bandwidth, then Click Apply.

You can fill in IP Address and Total Uplink Bandwidth and Total Downlink Bandwidth you want to restrain,  then Click Apply.

Application introduction: Settings Solution about how to configure WDS to TOTOLINK products.

● Before configuration, make sure that both A Router and B Router are powered on.

● Connect your computer to the same network of router A and B.

● move the B router closer to the A router to find the B routing signals better for fast WDS.

● A Router and Router should be set to the same channel.

● Set both Router A and B should to the same band 2.4G.

● Choose the same models for A-router and B-router. If not, WDS function may not be implemented.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3: A-router setting

3-1. Firstly connect the Internet for A-router then please go to Wireless ->WDS Settings page, and check which you have selected.(The type of A-router and B-router should be same )

Select Enable, then Input MAC Address of B-router in A-router , then Click Add.

3-2. Please go to Wireless->Basic Settings page, select Channel Number which you must choice equal for the B-router.

STEP-4: B-router setting

4-1. Secondly use Bridge Mode for B-router then please go to Wireless ->WDS Settings page, and check which you have selected.

Select Enable, then Input MAC Address of A-router in B-router and Select Auto for Data Rate, then Click Apply.

4-2. Please go to Wireless->Basic Settings page, select Channel Number which you must choice equal for the A-router.

Check the label on the bottom of the router to get the login address of the router, as shown below.

Product sticker	Default login address
	itotolink.net
	192.168.0.1
	192.168..1

Obtain the login address of the router through the computer (take win10 system as an example).

STEP-1:

The computer connects to the wireless signal of the router. (The back sticker has the factory default wireless signal name)

STEP-2: 

2-1. Click on wireless icon at the bottom right corner on the screen, Select Network & Internet settings.

2-2. Select the connected wireless network.

2-3. Select Details to check whether an IP address is obtained.

If the IPV4 address is 192.168.0.*, the default gateway of IPV4 is 192.168.0.1, indicating that the login address of the router is 192.168.0.1.

If the IPV4 address is 192.168.1.*, the default gateway of IPV4 is 192.168.1.1, indicating that the login address of the router is 192.168.1.1.

If the IP is not available, you can disconnect the signal and reconnect it. If it is still invalid, you can restore the router to the factory and check the IP address obtained after the connection signal.

Note: Before this, please confirm that your computer is selected to "acquire IP address automatically".

For the setting method of the computer automatically obtaining the IP address, refer to the following figure (take win10 system as an example).

Obtain the login address of the router through your mobile phone.

STEP-1

The wireless signal that the phone connects to the router. (The back sticker has the factory default wireless signal name)

STEP-2:

Select your phone's wireless network settings to check if you have an IP address.

At this point, the IPV4 address is 192.168.0.*, and the IPV4 default gateway is 192.168.0.1, indicating that the router's login address is 192.168.0.1.

STEP-3: 

Enter 192.168.0.1 in the address bar of the mobile browser.

STEP-4:

If you still can't enter, you can change the browser or a mobile phone or computer through the 192.168.0.1 login interface.

STEP-5: 

If the fourth step is invalid, the router can be reset.

Reset method:

1. Please make sure your router’s power is on regularly, then press the RST button for about 10s.(The RESET pin should be held with a pointed object such as a paper clip or a pen tip)

2. Loosen the button until your router’s LED lights all flashing, then you have reset your router to default settings.

Application introduction: This article will illustrate way to manually set an IP address on Windows 10/Mobile phone.

Manually set IP address on Windows 10

1-1. Find the small computer icon in the lower right corner of your computer desktop ，click on “Network & Internet settings”.

1-2. Pop up the Network & Internet Center interface, click on “Change adapter options” under Related settings.

1-3. After open changing adapter options,find Ethernet,click and select Properties.(If you want to check the wireless IP address, find WLAN)

1-4. Select “Internet Protocol Version 4 (TCP/IPv4)”,click on “Properties”.

1-5. To manually set IP address, select “Use the following IP address”, set the IP address and subnet mask; Finally click on“ok”.Take the IP address 192.168.0.10 as an example.

1-6. When you don't need to set the IP address manually, Please select Obtain an IP address automatically and Obtain DNS Server address automatically.

Manually set IP address on Mobile phone

1-1. Click Settings on the screen-> Wireless Network (or Wi-Fi), click on the exclamation mark behind the wireless signal.

Note: Before manually set IP address , make sure the wireless terminal is currently connected or is connecting to the wireless signal.

1-2. Click Static, enter the corresponding parameters in the IP address, gateway, and network mask positions, and click Save. Take the IP address 192.168.0.10 as an example.

1-3. When you don't need to set the IP address manually, Please turn off static IP.

Application introduction: To enter the router’s setting interface, you may enter the specified IP if you know setup your PC or set your PC to obtain an IP address automatically.

The steps for configuring TCP/IP properties (Here I take system W10 for example).

STEP-1: 

Click on   at the bottom right corner on the screen

STEP-2: 

Click on [Properties] button in the lower left corner

STEP-3:

Double click on “Internet Protocol (TCP/IP)”

STEP-4: 

Now you have two ways to configure the TCP/IP protocol below:

4-1. Assigned by DHCP Sever

Select Obtain an IP address automatically and Obtain DNS Server address automatically, as shown in the figure below. These may be selected by default. Then click OK to save setting.

4-2. Assigned manually

Using the following IP Address, as shown in the following figure.

[1] If the router’s LAN IP address is 192.168.1.1, please type in IP address 192.168.1.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.1.1.

[2] If the router’s LAN IP address is 192.168.0.1, please type in IP address 192.168.0.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.1.

STEP-5:  

Check the IP address you get automatically in the former step

The IP address is 192.168.0.2, it means the network segment of your PC is 0, you should enter http://192.168.0.1 into the address bar of your browser.

Enter the router’s setting interface similarly and do some settings.

Application introduction:This article describes the Windows operating system computer connected to the router (or other network device) by wireless or wired, view the gateway IP address of the current router.

For Windows W10:

STEP-1. TOTOLINK Router LAN Port Connects the PC Or wirelessly connect to TOTOLINK Router WIFI.

STEP-2. Right-click the Network Connections icon, click on “Network & Internet settings”.

STEP-3. Pop up the Network & Internet Center interface, click on “Network and Sharing Centre” under Related settings.

STEP-4. Click connections target

STEP-5. Clink Details…

STEP-6. Find to IPv4 Default Gateway, This is the current gateway address of your router.

For Windows 7，8, 8.1 and 10:

STEP-1. Click on windows key+ R key on the keyboard at the same time. 

   ‘R’

STEP-2. Enter cmd in the field and click OK button.

STEP-3. Type in ipconfig and click enter key. Find to IPv4 Default Gateway, This is the current gateway address of your router.

If you can’t login the web interface of TOTOLINK, it may be related to factors such as router, line, browser or computer. 

Please follow the steps below for detailed troubleshooting.

Application introduction:       

After entering the management address of the router in the address bar of the browser, the management page cannot be displayed, or the page cannot be displayed after entering the management password, as shown below.

Note: Ensure that the login IP address you typed in the address bar is correct, as well as the login username and password. 

STEP-1: Check line connection

The operating computer should be connected to the router and can be connected via a network cable or wirelessly.

Connect through the network cable:

Operate the computer and connect to the LAN port of the router, and ensure that the indicator of the computer network cable interface and the corresponding interface of the router is on.

Wireless connection: 

The wireless terminal needs to connect to the router signal. When the factory setting is set, the router default Wi-Fi name and password are printed on the bottom label of the router.

Note: If the signal of the wireless router is not found, it is recommended to reset the router.

STEP-2: Check computer IP address

If the computer does not specify or obtain the correct IP address, it will be unable to log in to the management interface.

Be sure to set the IP address of the operating computer to be automatically obtained. Take the Windows 10 system wired network card as an example. For the setting method of the computer automatically obtaining the IP address, refer to the following figure.

STEP-3: Check login address

TOTOLINK router currently has three types of login addresses, and different router addresses may be different:

Management page address: itotolink.net or 192.168.0.1 or 192.168.1.1.

For the specific login address, please check the sticker at the bottom of the router, as shown below (take itotolink.net as an example).

After confirming the login address, open the browser, clear the address bar and enter the management address, press Enter, as shown below.

STEP-4: Check login password

If the password input box of the login management interface can be displayed, but the wrong password is entered, the management interface cannot be logged.

Our common default login password prompt box, as shown below.

Note: If you forget the set or modified management password, you can only restore the factory settings.

STEP-5: Change your browser or computer

A. Change browser and clear browser cache

Try changing your browsers like Google Chrome, Firefox, Internet Explorer, etc., and clear your browser cache.

Delete cookies on the web browser. Here we take Google Chrome for example.

Note: In general, the browser enters the management address of the router and a 404 error pops up. Please use this method first.

B. Try to log in with your phone

If you are unable to log in using your computer, you can try to change another computer or use your mobile phone to log in to the management interface (using the mobile browser), as shown below, enter itotolink.net as an example.

STEP-6: Reset router

If you still cannot log into the router's setup page after troubleshooting according to the above methods, it is recommended to restore the factory settings. There are two types of wireless router reset buttons: RESET pin and RESET button. As shown below.

Reset method:

1. Please make sure your router’s power is on regularly, then press the RST button for about 10s.(The RESET pin should be held with a pointed object such as a paper clip or a pen tip)

2. Loosen the button until your router’s LED lights all flashing, then you have reset your router to default settings.

Note: Some wireless routers share a button with RESET.

Application introduction: 

Some TOTOLINK products have more than one hardware version, using V1, V2, etc for separation, and generally, each hardware version corresponds to a specifically developed firmware. 

If you want to upgrade your device to the latest firmware, you need to choose the correct firmware version for your device. 

【 CAUTION 】

All content on this website is only applicable to models selling in overseas markets (outside China   mainland, Taiwan and South Korea ),  any model purchased from China mainland,Taiwan or South Korea caused damage by upgrading software on this website is excluded in after-sales service range

For most TOTOLINK products, you can see a bar coded sticker at the front of the device, there is a  character string “VX.Y” (for example, V1.1), See below:  

The number X is the Hardware Version of your device. If the string shows “V1.y”, it means the hardware version is V1.

Application introduction: If you want to manage your router anywhere on the network, you can configure it in real time and securely. The remote WEB management function enables remote management of the router where it is connected to the Internet.

Take A3000RU as an example:

STEP-1: Login to the TOTOLINK router in your browser;

STEP-2: In the left menu, click System Status, check the WAN IP address and remember.

STEP-3: In the left menu, click Management ->Management-Remote. Select Enable, Input the remote port. Then click Apply.

[Note]:

The remote WEB management port set by the router is only needed when the external network computer accesses the router. Local area network computer access router is not affected and still uses 192.168.0.1 access.

STEP-4: In external network, use WIN IP address + port access, as shown below:

1. The service provider shields the corresponding port;

Some broadband service providers may block common ports such as 80, resulting in inaccessibility of the router interface. It is recommended to set the WEB management port to 9000 or higher. The external network user uses the set port to access the router.

2. WAN IP must be the public IP address;

The computer in the LAN accesses http://www.apnic.net. If the IP address is different from the IP address of the router's WAN port, the IP address of the WAN port is not the public IP address, which prevents the external network user from directly accessing the router interface. It is recommended to contact the broadband service provider to solve the problem.

3. WAN IP address has changed.

When the Internet access mode of the WAN port is dynamic IP or PPPoE, the IP address of the WAN port is not fixed. When using the external network access, you need to confirm the IP address of the router WAN port.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

If don’t want to restore the router to the factory settings, please follow the introduction below.

3-1. Connect your computer to the router by cable or wireless

3-2. Setup you PC to get the IP automatically (Here I take system W10 for example)

3-3. Click on   at the bottom right corner on the screen

3-4. Click [ Properties ] button in the lower left corner

3-5. Double click on “Internet Protocol (TCP/IP)”.

STEP-4:

Now you have two ways to configure the TCP/IP protocol below:

4-1. Assigned by DHCP Sever

[1] Select Obtain an IP address automatically and Obtain DNS Server address automatically, as shown in the figure below. These may be selected by default. Then click OK to save setting.

[2]Check the IP address you get automatically

The IP address is 192.168.0.2, it means the network segment of your PC is 0, you should enter http://192.168.0.1 into the address bar of your browser.

Enter the router’s setting interface similarly and do some settings.

4-2. Assigned manually

Using the following IP Address, as shown in the following figure.

[1] If the router’s LAN IP address is 192.168.1.1, please type in IP address 192.168.1.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.1.1.

Then enter http://192.168.1.1 to log in to the router.

[2] If the router’s LAN IP address is 192.168.0.1, please type in IP address 192.168.0.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.1.

Then enter http://192.168.0.1 to log in to the router.

Note: After the router is successfully set up, your computer must choose to obtain an IP address automatically to access the network.

Application introduction: WISP mode, all ethernet ports are bridged together and the wireless client will connect to ISP access point. The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN.

● Before configuration, make sure that both A Router and B Router are powered on.

● make sure you know the SSID and password for A router 

● 2.4G and 5G, you can only choose one for WISP

● move the B router closer to the A router to find the B routing signals better for fast WISP

1. B router can use PPPOE, static IP. DHCP function.

2. WISP can build its own base stations in public places such as airports, hotels, cafes, teahouses and other places, providing wireless Internet access services.

STEP-1 B-Router Wireless Setup

You need to enter the Advanced Setup page of the router B, then follow the steps illustrated.

① ② set 2.4G network -> ③④ set 5G network 

⑤ Click the Apply button

STEP-2 B-Router Repeater Setup

Enter the settings page of the router B, then follow the steps illustrated.

① Click Operation Mode> ② Select WISP Mode-> ③ Click Next button

④ In next page, you should click Scan 2.4G or Scan 5G

⑤ Choose the WIFI SSID you need to make the WISP

Note: This article set to A router as an example

⑥ Enter the password for the WISP router

⑦ Click connect

STEP-3 B Router Position Display

Move the Router B to a different location for a best Wi-Fi access. 

Application introduction: By port forwarding, the data for Internet applications can pass through the firewall of the router or gateway. This article will show you how to forward ports on your router, take A3000RU as an example.

STEP-1:

In the left menu of the web interface, click Firewall ->Port Forwarding ->Enable

STEP-2:

Select the port protocol; Click Scan

STEP-3:

Select the PC IP address;

STEP-4:

Input the port you need and note; Then click Add.

STEP-5:

Ensure that the port successfully added to the Current Port Forwarding List.

The router's port forwarding settings are complete

Here with FTP server as an example (WIN10), check that the port forwarding is successfully.

1. Open the Control Panel\All Control Panel Items\Administrative Tools\Add FTP Server.

2. Input the ftp site name, Select the path; Click next.

3. Select the target PC address，Sets the port, Click Next;

4. Define users and permissions, Click Finish.

5. Now, you can access FTP over a LAN, Login Address: ftp://192.168.0.242;

6. Check ROUTER WAN IP, in the public network use it to log into the FTP Server; 

E.g ftp://113.90.122.205:21;

Normal visit,verify that the port forwarding OK

Application introduction:  Settings Solution about how to configure WDS to TOTOLINK products. Take the A3000RU as the example of setting 2.4G wireless.

● Before configuration, make sure that both A Router and B Router are powered on.

● Connect your computer to the same network of router A and B.

● move the B router closer to the A router to find the B routing signals better for fast WDS.

● A Router and Router should be set to the same channel.

● Set both Router A and B should to the same band 2.4G or 5G.

● Choose the same models for A-router and B-router. If not, WDS function may not be implemented.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3: A-router setting

3-1. Firstly connect the Internet for A-router then please go to Wireless 2.4GHz->WDS Settings page, and check which you have selected.(The type of A-router and B-router should be same )

Select Enable, then Input MAC Address of B-router in A-router. Click Add.

3-2. Please go to Wireless 2.4GHz ->Basic Settings page, select Channel Number which you must choice equal for the B-router.

STEP-4: B-router setting

4-1. Firstly connect the Internet for A-router then please go to Wireless 2.4GHz->WDS Settings page, and check which you have selected.(The type of A-router and B-router should be same )

Select Enable, then Input MAC Address of B-router in A-router. Click Add.

4-2. Please go to Wireless 2.4GHz ->Basic Settings page, select Channel Number which you must choice equal for the A-router.

Application introduction:  Repeater Mode, you can extend the superior Wi-Fi signal by Repeater setting function under the Wireless column to increase the coverage of the wireless signal.

● Before configuration, make sure that both A Router and B Router are powered on.

● make sure you know the SSID and password for A router 

● 2.4G and 5G, you can only choose one for Repeater

● move the B router closer to the A router to find the B routing signals better for fast repeater.

You need to enter the settings page of the router B, then follow the steps illustrated.

① Set 2.4G network -> ② Set 5G network -> ③ Click the Apply button

STEP-2 B-Router Repeater Setup

Enter the Advanced Setup page of the router B, then follow the steps illustrated.

① Click Operation Mode> ② Select Repeater Mode-> ③ Click Next button

④ In next page, you should click Scan 2.4G or Scan 5G

⑤ Choose the A-Router SSID you need to make the Repeater

Note: This article set to A router as an example

⑥ Enter the password for the Repeater router

⑦ Click connect

STEP-3 B Router Position Display

Move the Router B to a different location for a best Wi-Fi access.

Application introduction: Solution about how to control the time of surfing the Internet by wi-fi for TOTOLINK products.This document takes N600R as an example.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Please go to Wireless ->Wireless Schedule, and check which you have selected.

Select Enable and time you want to restrain in to surf the Internet, then Click Apply.

Application introduction: Solution about how to reset TOTOLINK products to factory defaults.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3: Login page reset

Please go to Management->System Configuration page, and check which you have selected.Select Restore.

STEP-4: RST Button reset

Please make sure your router’s power is on regularly, then press the RST button for about 5~8s.

Loosen the button until your router’s LED lights all flashing, then you have reset your router to default settings.

Application introduction: Solution about how to configure Internet mode with PPPoE ,Static IP and DHCP for TOTOLINK products

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3.1.1: Easy Setup DHCP setting

The Easy Setup page will turn up for basic and quick setting，Select DHCP as WAN Connection Type, then Click Apply.

STEP-3.1.2: Advanced Setup DHCP setting

Please go to Network ->WAN Setting page, and check which you have selected. Select DHCP Client as WAN Type, then Click Apply.

STEP-3.2.1: Easy Setup Static IP setting

The Easy Setup page will turn up for basic and quick setting，Selecting Static IP as WAN Connection Type and input your information about Static IP which you want to fill in .Then Click Apply

STEP-3.2.2: Advanced Setup Static IP setting

Please go to Network ->WAN Setting page, and check which you have selected.

Select Static IP as WAN Type and input your information about Static IP which you want to fill in .Then Click Apply

STEP-3.3.1: Easy Setup PPPOE setting

The Easy Setup page will turn up for basic and quick setting ,Select PPPoE as WAN Type and input your PPPoE username and password which are provided by your ISP. Then Click Apply

STEP-3.3.2: Advanced Setup PPPOE setting

Please go to Network ->WAN Setting page, and check which you have selected.

Select PPPoE as WAN Type and input your PPPoE username and password which are provided by your ISP. Then Click Apply

Application introduction: MAC address is the physical address of your computer’s network card. Generally, every network card has one unique Mac address. Since many ISPs only allow one computer in LAN to access Internet, users can enable MAC address clone function to make more computers surf Internet.

Following these steps:

1. Connect you PC to the router by cable or wireless.

2. Typing 192.168.0.1 in the address bar of you browser.

3. Input the user name and password, both are admin by default.

4. Click Network->WAN Settings, Select the WAN type and click clone MAC. Finally click Apply. 

Application introduction: The Wireless SSID and password are the basic information for you to connect Wi-Fi network. But sometimes you may forget or want to change them regularly, so here we will guide you how to check or modify the wireless SSID and password.

STEP-1: Enter the setup interface

Open a browser,enter 192.168.0.1. Input User Name and password (default admin/admin) on login management interface,as follows:

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2: View or modify the wireless parameters

2-1. Check or modify in Easy Setup page.

Login management interface, first enter the Easy Setup interface, you can see wireless settings, as follows:

If you are setting up the WIFI SSID and password for the first time, you can modify the SSID in the wireless settings and recommend selecting Encryption: WPA / WPA2-PSK (default Disable) and then modify the WIFI password.

2-2. Check and modify In the Advanced Setup

If you also need to set more parameters for WiFi, you can enter the Advanced Setup interface to set up.

In the wireless ---Basic settings, you can set the SSID, Encryption, Password, Channel and other information

In the wireless ---Advanced settings, you can set the Preamble Type, TX Power, Maximum of connected users and other information

Q1: Can wireless signals be set to special characters?

A: Yes, WIFI SSID and WIFI passwords can be set to special characters

SSID is only allowed to include Chinese and English, numbers, and special characters : ! @ # ^ & * () + _- = {} []:and space character

WPA Key can contain only English, numbers and the following special character : ! @ # ^ & * () + _- = {} []

Forget the router's user name and password, how to do?

Application introduction: Just like the keys on the door, the management password (login password) is the credentials of the login router. If you forget your router's management password, like losing the pocket of the key, is unable to enter the house.

Note: The login window will show the router model, please be sure to be your own router interface.

STEP-1: Try entering a password

If you do not forget to set a good password, you can only restore the router factory settings, no super password. Before returning to the factory, try entering a possible management password.

If the two methods suggest that the password is wrong, please restore the router to factory settings, that is, reset the router.

STEP-2: Restore the router to factory settings

In the router shell side to find the router Reset button.

The router is working properly, hold down the Reset button for more than 5 seconds, release the button. When all the indicators are lit, it indicates that the reset is successful.

Note: After restoring to factory settings, all configurations change to their default values.

STEP-3: Restore the router to Re-set

1.open the browser;

2.enter the gateway: 192.168.0.1 or 192.168.1.1;

3.enter the default login account and password: admin admin;

4.login interface;

5.Quickly set the Internet and wireless settings;

6.Click on the Apply,wait 50s;

7.Click Advanced Setup;

8.Enter Management ---> Administrator Setting screen;

9.Enter the old password (admin) and set the new password twice:

10.Click Apply,setup is complete.

Q1: Can I get a password without resetting?

If you forget to set the password, you can only reset the router. The configuration(settings, account password, etc.) in the router disappears and needs to be reset. If it is a commercial router with a serial port, you can try to retrieve through the serial port. 

Q2: Reset button (Reset) is broken or can’t be reset successfully, how do?

Please follow the reset operation in strict accordance with the instructions, if the operation can’t be reset after a number of operations (that is, the indicator light is not flash, bright, full bright reset the performance of the state), there may be reset key hardware problems need to follow the after-sales process.

Q3: How are the settings are wrong password?    

Password error is certainly a reason, if the reset is prompted after the error, the following may be:

A. Do not follow the prompts on the page to set, please be sure to see the request to enter the user name password;

B. The login page is not your router, it may be the wrong connection to the cat, into the cat interface.If the interface does not display the correct router model, please re-confirm and connect;

C. The browser cache is causing you to try to replace the browser or clear the cache.

Q4: Use third-party software to manage router descriptions 

Our router does not support third-party software management, does not recommend the use of such software, please use the browser management.

Like can’t enter the house, there may be lost the key, take the wrong key, into the wrong door, etc., there is a specific reason, need to observe and carry out effective operation try, as soon as possible to resume normal use. In addition, also need to back up important configuration, record the password to prevent forgetting.

Application introduction:  Solution about how to configure multiple SSID for TOTOLINK products.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Please go to Wireless ->Multiple APs page, and check which you have selected.

Select Enable, then Input your own SSID and Key, then Click Add. So you can repeat this operation for Multiple SSID.

Application introduction: Solution about how to configure Wireless MAC Filtering on TOTOLINK router

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Please go to Firewall ->MAC Filtering page, and check which you have selected.Select Enable, then Input your own MAC Address which you want to restrict or click Scan  bottom to restrict it and give a Comment for this item, then Click Add.

Note: You need add items in this way one by one.

Application introduction: Solution about how to configure IP Address and Port Filtering on TOTOLINK 

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Please go to Firewall ->IP/Port Filtering page, and check which you have selected.Select Enable, then Input your own IP Address and Port Range which you want to restrict or click Scan bottom to restrict it and give a Comment for this item, then Click Add.

Note: You need add items in this way one by one.

Application introduction:  This router has a built-in real time clock which can update itself manually or automatically by means of Network Time Protocol (NTP). As a result, you can schedule the router to dialup to the Internet at a specified time, so that users can connect to the Internet only during certain hours. 

STEP-1:

Please login to the web-configuration Interface of the router.

STEP-2: Check Time Setting

Before using schedule function you have to set your time correctly.

2-1. Click Management->Time Setting in the sidebar.

2-2. Enable NTP client update and choose the SNTP server, click Apply.

STEP-3: Wireless Schedule Setup

3-1. Click Management->Wireless Schedule

3-2. Enable the schedule at first, in this section, you can setup the specify time so the WiFi will be on during this period.

The picture is a example, and WiFi will be on from eight o’ clock to eighteen o’clock on Sunday.

Application introduction: If you can’t access the router’s setup interface or simply forgot the router’s password, you may reset the current configuration to factory default. There are two ways to. 

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Click Management->System Configuration on the navigation bar on the left.

STEP-4:

Click Restore Factory Default to reset the router’s configuration.

STEP-5:

Click OK and wait for few seconds to finish resetting. 

Only by one click on the RST/WPS button 

STEP-1:

Press and hold the RST/WPS button for about 10 seconds, until the CPU led blink quickly.

STEP-2:

After nearly 30 seconds, resetting is finished.

Application introduction: TOTOLINK router provided repeater function, with this function users can expand the wireless coverage and allow more terminals to access Internet.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

You need to enter the settings page of the router B, then follow the steps illustrated.

① Set 2.4G network -> ② Set 5G network -> ③ Click the Apply button.

STEP-4:

Please go to Operation Mode ->Repteater Mode->Next, then Click Scan 2.4GHz orScan 5GHz and select host router’s SSID.

STEP-5

Select host router’s Password you want to fill in, then Click connect.

Note: 

After completing the above operation, please re-connect your SSID after 1 minute or so.if the Internet is available it means that the settings are successful. Otherwise, please re-set the settings again

Questions and answers

Q1: After the Repeater mode is set successfully, you cannot log in to the management interface.

A: Since AP mode disables DHCP by default, the IP address is assigned by the superior router. Therefore, you need to set the computer or mobile phone to manually set the IP and the network segment of the router to log in to the router settings.

Q2: How do I reset my router to factory settings?

A: When turning on the power, press and hold the reset button (reset hole) for 5~10 seconds. The system indicator will flash quickly and then release. The reset was successful.

Application introduction: The schedule function allows you to setup the time that the router will reboot automatically. What’s more, it allows you to setup the time WiFi on and off while by the other times beyond this period WiFi will be off. It is very convenient for users who often access the Internet very regularly.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3: Check Time Setting

Before you configure the schedule, you should make sure that the NTP Server is enabled.

3-1. Click Management->Time Setting in the sidebar.

3-2. Choose Enable NTP and click Apply.

STEP-4: Reboot Schedule Setup

4-1. Click Management->Reboot Schedule in the navigation menu.

4-2. In the schedule interface, you can setup the time when the router will reboot time.

4-3. Or set the countdown time.

Application introduction: If you want to reset the router’s User Name and Password, please follow the steps below.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Click Management->Administrator Setting on the navigation bar on the left. In this interface, you can change the password after entering the old password.The default user name and password is admin.

Application introduction: Multiple APs function allows users to create network name for clients or friends accordingly. It is good for access control and your data privacy.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Click Wireless->Multiple APs on the navigation bar on the left. In this interface, you can add other SSIDs with different encryption type. If you want to hide the SSID, choose “Disable” in the SSID broadcast bar. Then click Apply.

Note: 

You can no longer see the hidden SSID. If you want to connect to the SSID, you must manually enter the correct SSID search.

Application introduction: IP conflict may happen while there are two routers in series connection or other reasons, which may cause false connection. Change LAN IP by follow steps can help you avoid of IP conflict.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Click Network->LAN Settings on the navigation bar on the left. In this interface you can change the IP address (e.g. 192.168.2.1), and click Apply button for saving settings.

Take N200RE-V3 as an example.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Then the Easy Setup page will turn up for basic and quick settings, including Internet Setting and Wireless Setting.

STEP-4:

Click Advanced Setup, you can go to the router’s User Interface.

Application introduction: Ping is used to test connectivity to a specific host in the network with the use of Internet Protocol (IP) address or a specific website URL.

STEP-1. Click Start-> Run.

STEP-2. Enter cmd in the field and click OK button.

STEP-3. Type in Ping 192.168.1.1 and click enter key.

For Windows 7，8, 8.1 and 10:

STEP-1. Click on windows key+ R key on the keyboard at the same time. 

 +‘R’

STEP-2. Enter cmd in the field and click OK button.

STEP-3. Type in Ping 192.168.1.1 and click enter key.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

First, the Easy Setup page will turn up for basic and quick settings, you can find the short firmware version on the top left corner. See below picture:

STEP-4:

For full firmware version, please click Advanced Setup on top right corner. The System Status will show you full firmware version. See below red marked area:  

For most TOTOLINK routers, you can see two bar coded stickers at the front of the device, the character string started with Model No.(for example N200RE) and ended with Hardware Version (for example V2.0) is the serial number of your device. See below:

Application introduction: Password can ensure the security of your wireless network. In case you forget the Password, follow steps below to restore it.

Take N200RE-V3 as an example.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

First, the Easy Setup page will turn up for basic and quick settings, click Advanced Setup.

STEP-4:

Click Wireless Setting->Basic Settings on the left navigation bar.

STEP-5:

You can check the password on this page directly.

Take N200RE-V3 as an example.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

First, the Easy Setup page will turn up for basic and quick settings, including Internet Setting and Wireless Setting.

STEP-4:

Choose the WAN Access Type, enter User Name, Password provided by your ISP. Set an encryption method and password for your WiFi network. Click Apply to make the settings work.

STEP-5:

For successful connection, the Connect Status will show you connected. 

Application introduction: In order to improve network security, you can disable SSID broadcast in the web-configuration interface. After disabled SSID broadcast, other devices can find and connect to the SSID again.

STEP-1: Connect your computer to the router

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

Now you have logged into the web interface of the router. 

STEP-3: Disabled SSID broadcast

Click Wireless-> Basic Settings.On this page, you could change the SSID Broadcast status.

Application introduction: TOTOLINK router provided repeater function, with this function users can expand the wireless coverage and allow more terminals to access Internet.

Set a encrypted wireless network, please following these steps.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Click Wireless Settings->Wireless Setup on the left menu.

STEP-4:

In this interface, you can encrypt your network now.

WEP-Open System, WEP-Shared Key, WPA-PSK, WPA2-PSK and WPA/WPA2-PSK are provided for your, for better security, WPA/WPA2-PSK is recommended.

Application introduction: When you can’t find the SSID of the router even you have powered on the router? you can check the settings following these steps.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Click Wireless->Basic Settings in from the menu on the left.Make sure the SSID Broadcast item is enabled and then choose the appropriate channel.

STEP-4:

After saving your settings, scan wireless signal again.

Application introduction: Password can ensure your security of your wireless network. Follow these steps if you forgot about it.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Click Wireless->Basic Settings on the navigation bar on the left.In this interface, you can see the password you ever setup and change it if necessary.

Application introduction: If you want to alter the SSID of the router, please follow the steps below.

STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Click Wireless->Basic Settings on the navigation bar on the left. To change the SSID, you can input the new SSID to replace the original SSID. If you want to hide the SSID, choose “Disable” in the SSID broadcast bar. Then click “Apply” in the lower right corner. 

Application introduction: IEEE 802.11ac is a wireless computer networking standard in the 802.11 family, developed in the IEEE Standards Association process, providing high-throughput wireless local area networks (WLANs) on the 5 GHz band.

Comparison of Wireless-AC and Wireless-N technologies:

1. Throughput

The 802.11n Wi-Fi connections max out at around 150Mbps with one antenna, 300Mbps with two and 450Mbps with three antennas. 802.11ac connections will be roughly three times faster - so that's 450Mbps, 900Mbps and 1.3Gbps respectively.

2. Channel Bandwidth

Mandatory 80 MHz channel bandwidth for stations, 160 MHz available optionally

40 MHz maximum in 802.11n

3. Modulation

256-QAM, rate 3/4 and 5/6, added as optional modes in 802.11ac

64-QAM, rate 5/6 maximum in 802.11n

4. MIMO spatial streams

Up to eight spatial streams in 802.11ac (vs. four in 802.11n)