Application introduction:

This article describes how to quickly make a wireless connection through the router's WPS button.

Diagram

Set up steps

STEP-1:

* Please make sure your router has WPS button before setting.

* Please make sure your wireless client supports WPS functionality before setting.

STEP-2:

Press WPS button on the router for 1s, WPS enabled. There are two types of wireless router WPS buttons: RST/WPS button and WPS button. As shown below.

2-1. RST/WPS button：

2-2. WPS button：

Note: If router is a RST/WPS button, no more than 5s, router will be reset to factory defaults if you press it for more than 5s.

STEP-3:

After pressing the WPS button, use wireless client to connect to the router WIFI signal. Using Computer and Mobile phone wireless connection as an example. As shown below.

3-1. Computer wireless connection:

3-2. Mobile phone  wireless connection:

Application introduction:

Repeater mode expands the upper-level wireless signal by wireless to extend the wireless signal to a farther distance. Here is an example of A1004.

Diagram

Set up steps

STEP-1：Assigned manually IP address

A1004 LAN IP address is 192.168.0.1, please type in IP address 192.168.0.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.1.

STEP-2：Login to the management page

Open the browser,clear the address bar,enter 192.168.0.1 to the management page，click Advance setup.

The repeater mode supports both 2.4G and 5G. Here's how to set up 2.4G first, then set 5G.

STEP-3：2.4G repeater settings

3-1.  2.4GHz wireless setting

❶ Click Wireless Setup -> ❷Select 2.4GH Basic network -> ❸ Set Wireless SSID -> ❹ Set Wireless Password -> ❺ Click Apply.

3-2.  2.4GHz extension setting

❶ Click Wireless Multibridge -> ❷ Select 2.4GHz -> ❸ Select Repeater -> ❹ Click AP Scan -> ❺ Select the wireless you need to expand -> ❻ Enter the upper-level wireless password, and finally ❼ click Apply.

STEP-4：5G repeater settings

4-1.  5GHz wireless setting

❶ Click Wireless Setup -> ❷ Select 5GH Basic network -> ❸ Set Wireless SSID -> ❹ Set Wireless Password -> ❺ Click Apply.

4-2.  5GHz extension setting

❶ Click Wireless Multibridge -> ❷ Select 5GHz -> ❸ Select Repeater -> ❹ Click AP Scan -> ❺ Select the wireless you need to expand -> ❻Enter the upper-level wireless password, and finally ❼ click Apply.

STEP-5：

After the setting is successful, please obtain the IP setting automatically, and the computer can connect to the network.

STEP-6：

Now all Wi-Fi enabled devices can connect to a custom wireless network.

FAQ Common problem

Q1: After the bridge mode is set successfully, you will not be able to access the router. If you need to revisit, there are two ways!

1. Press the reset button/hole on the router to restore the router to factory settings;

2. Log in to the router management page by setting a fixed IP (refer to STEP-1).

It is suitable for:　 A3, A1004

Application introduction:

The system log of the router can be used to find out why the network connection fails.

Set up steps

STEP-1:

Open the browser, clear the address bar, enter 192.168.0.1, select Advance Setup.fill in the administrator account and password (default admin), click Login, as follows:

STEP-2:

Make sure your router is connected to the internet.

STEP-3:

In the left menu, click System -> System Log.

STEP-4:

Administrator email settings.

①Fill in the recipient email, for example: fae@zioncom.net

②Fill in the recipient server, for example: smtp.zioncom.net

③Fill in the sender's email.

④Fill in the sender's email and password.

⑤Click "Apply".

STEP-5:

Click Send E-mail lmmediately, click OK.

Note:

Before sending an email, you need to make sure the router is connected to the internet.

STEP-1: Difference of 2.4G and 5G Wi-Fi

1-1.The primary difference between the 2.4 GHz and 5GHz wireless frequencies is range as the 2.4GHz frequency is able to reach farther than the 5GHz frequency. This is a result of the basic characteristics that waves attenuate much faster at higher frequencies. So if you are more concerned with the coverage, you should select 2.4GHz rather than 5GHz.

1-2.The second difference is the number of devices on the frequencies. 2.4GHz suffers more interference than 5GHz.

1). The older 11g standard only uses the 2.4GHz frequency, majority of the world is on it. 2.4 GHz has fewer channel options with only three of them non-overlapping, while 5GHz has 23 non-overlapping channels.

2). A lot of other devices are also on the 2.4 GHz frequencies, the biggest offenders are microwaves and cordless phones. These devices add noise to the medium that can further decrease the speed of wireless networks.

In both aspects, choosing to deploy on the 5GHz frequency is the much better option as you have more channels to use to isolate yourself from other networks and there are far fewer interference sources.

But the radar and military frequency is also 5GHz, so 5GHz wireless may also have some interference, and many countries require that wireless devices working on 5GHz should support DFS(Dynamic Frequency Selection) and TPC(Transmitting Power Control).

STEP-2: Summary

3-1. All TOTOLINK dual band routers support 2.4GHz and 5GHz simultaneously；

3-2. 5GHz has a shorter range than 2.4GHz;

3-2. 5GHz radio band that offers high-speed wireless connection that could with less interference in compare to 2.4G WiFi network.

Application introduction: This article will illustrate way to manually set an IP address on Windows 10/Mobile phone.

Manually set IP address on Windows 10

1-1. Find the small computer icon in the lower right corner of your computer desktop ，click on “Network & Internet settings”.

1-2. Pop up the Network & Internet Center interface, click on “Change adapter options” under Related settings.

1-3. After open changing adapter options,find Ethernet,click and select Properties.(If you want to check the wireless IP address, find WLAN)

1-4. Select “Internet Protocol Version 4 (TCP/IPv4)”,click on “Properties”.

1-5. To manually set IP address, select “Use the following IP address”, set the IP address and subnet mask; Finally click on“ok”.Take the IP address 192.168.0.10 as an example.

1-6. When you don't need to set the IP address manually, Please select Obtain an IP address automatically and Obtain DNS Server address automatically.

Manually set IP address on Mobile phone

1-1. Click Settings on the screen-> Wireless Network (or Wi-Fi), click on the exclamation mark behind the wireless signal.

Note: Before manually set IP address , make sure the wireless terminal is currently connected or is connecting to the wireless signal.

1-2. Click Static, enter the corresponding parameters in the IP address, gateway, and network mask positions, and click Save. Take the IP address 192.168.0.10 as an example.

1-3. When you don't need to set the IP address manually, Please turn off static IP.

Application introduction: To enter the router’s setting interface, you may enter the specified IP if you know setup your PC or set your PC to obtain an IP address automatically.

The steps for configuring TCP/IP properties (Here I take system W10 for example).

STEP-1: 

Click on   at the bottom right corner on the screen

STEP-2: 

Click on [Properties] button in the lower left corner

STEP-3:

Double click on “Internet Protocol (TCP/IP)”

STEP-4: 

Now you have two ways to configure the TCP/IP protocol below:

4-1. Assigned by DHCP Sever

Select Obtain an IP address automatically and Obtain DNS Server address automatically, as shown in the figure below. These may be selected by default. Then click OK to save setting.

4-2. Assigned manually

Using the following IP Address, as shown in the following figure.

[1] If the router’s LAN IP address is 192.168.1.1, please type in IP address 192.168.1.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.1.1.

[2] If the router’s LAN IP address is 192.168.0.1, please type in IP address 192.168.0.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.1.

STEP-5:  

Check the IP address you get automatically in the former step

The IP address is 192.168.0.2, it means the network segment of your PC is 0, you should enter http://192.168.0.1 into the address bar of your browser.

Enter the router’s setting interface similarly and do some settings.

Application introduction:This article describes the Windows operating system computer connected to the router (or other network device) by wireless or wired, view the gateway IP address of the current router.

For Windows W10:

STEP-1. TOTOLINK Router LAN Port Connects the PC Or wirelessly connect to TOTOLINK Router WIFI.

STEP-2. Right-click the Network Connections icon, click on “Network & Internet settings”.

STEP-3. Pop up the Network & Internet Center interface, click on “Network and Sharing Centre” under Related settings.

STEP-4. Click connections target

STEP-5. Clink Details…

STEP-6. Find to IPv4 Default Gateway, This is the current gateway address of your router.

For Windows 7，8, 8.1 and 10:

STEP-1. Click on windows key+ R key on the keyboard at the same time. 

   ‘R’

STEP-2. Enter cmd in the field and click OK button.

STEP-3. Type in ipconfig and click enter key. Find to IPv4 Default Gateway, This is the current gateway address of your router.

Application introduction: 

Some TOTOLINK products have more than one hardware version, using V1, V2, etc for separation, and generally, each hardware version corresponds to a specifically developed firmware. 

If you want to upgrade your device to the latest firmware, you need to choose the correct firmware version for your device. 

【 CAUTION 】

All content on this website is only applicable to models selling in overseas markets (outside China   mainland, Taiwan and South Korea ),  any model purchased from China mainland,Taiwan or South Korea caused damage by upgrading software on this website is excluded in after-sales service range

For most TOTOLINK products, you can see a bar coded sticker at the front of the device, there is a  character string “VX.Y” (for example, V1.1), See below:  

The number X is the Hardware Version of your device. If the string shows “V1.y”, it means the hardware version is V1.

Application introduction: Ping is used to test connectivity to a specific host in the network with the use of Internet Protocol (IP) address or a specific website URL.

STEP-1. Click Start-> Run.

STEP-2. Enter cmd in the field and click OK button.

STEP-3. Type in Ping 192.168.1.1 and click enter key.

For Windows 7，8, 8.1 and 10:

STEP-1. Click on windows key+ R key on the keyboard at the same time. 

 +‘R’

STEP-2. Enter cmd in the field and click OK button.

STEP-3. Type in Ping 192.168.1.1 and click enter key.

Application introduction: IP conflict may happen while there are two routers in series connection or other reasons, which may cause false connection. Change LAN IP by follow steps can help you avoid of IP conflict.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon        to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: 

Click Advanced Setup->Network->LAN/DHCP Server on the navigation bar on the left.

STEP-3:

Alter LAN IP into 192.168.X.1 (“X” is in range of 2~254, e.g.192.168.2.1), and then click Apply& Restart button.

STEP-4:

Wait for 40 seconds until the progress bar finished and then you should use the new address to enter the setting interface later.

Application introduction: IEEE 802.11ac is a wireless computer networking standard in the 802.11 family, developed in the IEEE Standards Association process, providing high-throughput wireless local area networks (WLANs) on the 5 GHz band.

Comparison of Wireless-AC and Wireless-N technologies:

1. Throughput

The 802.11n Wi-Fi connections max out at around 150Mbps with one antenna, 300Mbps with two and 450Mbps with three antennas. 802.11ac connections will be roughly three times faster - so that's 450Mbps, 900Mbps and 1.3Gbps respectively.

2. Channel Bandwidth

Mandatory 80 MHz channel bandwidth for stations, 160 MHz available optionally

40 MHz maximum in 802.11n

3. Modulation

256-QAM, rate 3/4 and 5/6, added as optional modes in 802.11ac

64-QAM, rate 5/6 maximum in 802.11n

4. MIMO spatial streams

Up to eight spatial streams in 802.11ac (vs. four in 802.11n)

Application introduction: When there are too many PCs in LAN, it is difficult to set speed limit rules for every computer. You can use smart QoS function to assign equal bandwidth for each PC. 

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note:The default access address differs by model. Please find it on the bottom label of the product.

1-2. Please click Setup Tool icon           to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: Enable Smart QoS

(1). Click Advanced Setup->Traffic->QoS setup.

(2). Select Start, then Input Download Speed and Upload Speed, then Click Apply.

     Or you can fill in IP Address and Down and Up Speed you want to restrain,  then Click Apply.

Application introduction: The TOTOLINK Routers offer a URL filter feature that helps you to achieve your goal by just several steps on the web-gui. It could help to filter http websites by keywords or URL. Here we go with a A2004NS.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note:The default access address differs by model. Please find it on the bottom label of the product.

1-2. Please click Setup Tool icon         to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2:Follow the steps below to set

2-1. In Internet Access Control, first we should check the Input Type, then select the URL Filter Setup listed below.

2-2. Next we need to set the URL rules.

Note:

1.prefix can not add http: //

2.Some sites are not supported()

3.Once unsuccessful, you can try several times.

Application introduction: Solution about how to set repeater mode on TOTOLINK products.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note:The default access address differs by model. Please find it on the bottom label of the product.

1-2. Please click Setup Tool icon          to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: Wireless(2.4GHz) repeater setting

Please go to Advance Setup ->Wireless(2.4GHz)->Wireless Multibridge , and check which you have selected.

Select Use Wireless Bridge and WPAPSK/WPA2PSK+TKIP/AES in Encryption, then Click AP Scan.

Then select the host router’s SSID and way of Encryption ,then input password of the host router’s SSID and Click Apply. 

STEP-3: Wireless(5GHz) repeater setting

Please go to Advance Setup ->Wireless(5GHz) ->Wireless Multibridge , and check which you have selected.

Select Use Wireless Bridge in Mode and WPAPSK/WPA2PSK+TKIP/AES in Encryption, then Click AP Scan.

Then select the host router’s SSID and way of Encryption ,then input password of the host router’s SSID and Click Apply.

PS: After completing the above operation, please re-connect your SSID after 1 minute or so. if the Internet is available it means thatthe settings are successful. Otherwise, please re-set the settings again

Application introduction：Wireless signals generally refer to Wi-Fi, wireless SSID and wireless password is the wireless terminal to connect the router to the Internet the most important two information. The actual use of the process, if there is no connection on the wireless, forget the wireless password, you need to view or modify the signal SSID and password.

 Set up steps 

STEP-1: Enter the setup interface

Open the browser, clear the address bar, enter 192.168.1.1, select Setup Tool.fill in the administrator account and password (default admin admin), click Login, as follows:

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2: View or modify the wireless parameters

2-1. Check or modify in Easy Setup page

Click Wireless Setup(2.4GHz), Modify the SSID according to your preference. Select encryption method (default encryption is recommended)，Enter the password, if you need to clear the password, you can choose Unhide，click Apply.

Click Wireless Setup(5GHz), Modify the SSID according to your preference. Select encryption method (default encryption is recommended)，Enter the password, if you need to clear the password, you can choose Unhide，click Apply.

2-2. Check and modify In the Advanced Setup.

If you need to set more wireless parameters, you need to enter Advanced Setup --- Wireless (2.4GHz) or Advanced Setup --- Wireless (5GHz). And then select the parameters you need to change in the pop-up submenu.

Questions and Answers

Q1: After setting up the wireless signal, need to restart the router?

A: No need. After setting the parameters, wait a few seconds for the configuration to take effect.

Application introduction: If you want to set the wireless parameters of dual-band wireless router, please follow the steps below.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note:The default access address differs by model. Please find it on the bottom label of the product.

1-2. Please click Setup Tool        to enter the setup interface

1-3. Please login to the Web Setup interface (the default user name and password is admin).

1-4. Now you can log in the interface to set up.

STEP-2: Parameters setting

2-1.Choose Advanced Setup->Wireless (2.4GHz)->Wireless Setup.

From the option, you can setup wireless parameters of 2.4GHz band

2-2. Choose Advanced Setup->Wireless(5GHz)->Wireless Setup.

From the option, you can setup wireless parameters of 5GHz band

Note: You must select Start in the Operation bar firstly, after configuring the parameters, don’t forget to click Apply.

Application introduction: MAC address is the physical address of your computer’s network card. Generally, every network card has one unique Mac address. Since many ISPs only allow one computer in LAN to access Internet, users can enable MAC address clone function to make more computers surf Internet.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon         to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: 

2-1. Choose Basic Setup->Internet Setup

2-2. Select the WAN type and click MAC Address Clone, then click Search MAC Address. Finally click Apply. 

Application introduction: If you want to connect the android phone to the TOTOLINK router, please follow the steps below.

1. Open WLAN function of your phone

2. In the WLAN interface, click “Scanning” option, screen will show different SSID

3. Select the SSID you want to add, there will be a tip that remind you to input password, input the password 

4. Check the information

Now you connect your android phone to the TOTOLINK router successfully.

Application introduction: If you want to connect iphone to the TOTOLINK router, please follow the steps below.

1. Open WLAN function of your iphone

2. The iphone will search for wireless network automatically, and the screen will show different SSID

3.Click the SSID you want to add, there will be a tip that remind you to input password

4.Check the information

Now you connect your iphone to the TOTOLINK router successfully.

Application introduction: If your Win 7 computer connects to the new wireless network for the first time, you need to use PIN number to connect to the network. While you can’t find PIN number on the shell of the router, you can find it by these ways.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon           to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: 

Click Advanced Setup->Wireless->WPS Setup on the navigation bar on the left.

STEP-3: 

You can enter the PIN code in this interface to add WPS device.

STEP-4: 

You can also stop WPS function here for not use PIN number, and then set a WPA-PSK or WPA2-PSK encryption for security on the Wireless Setup interface.

Application introduction: In a particular situation, we need to let computer or other network devices use the same IP, we can realize it by only few simple steps.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon          to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2:

Click Advanced Setup->Network ->LAN/DHCP Server on the navigation bar on the left.

STEP-3:

Click Start button to start DHCP at first.

STEP-4:

4-1. Tick the box as the picture show and then enter the IP address specified in the blank, next to click Add button.

4-2. Then you can see the information about the IP/MAC address on the left side.

--Block MAC address on the list with wrong IP address:

The PC’S MAC address has existed on the rule but with the wrong IP can’t connect to Internet.

--Block MAC address not on the list:

The PC’s MAC address isn’t exists on the rule can’t connect to Internet

Application introduction:  In a particular situation, we need to let computer or other network devices use the same IP, we can realize it by only few simple steps.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

1-2. Please click Setup Tool icon          to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2:

Click Advanced Setup->Network ->LAN/DHCP Server on the navigation bar on the left.

STEP-3:

Click Start button to start DHCP at first.

STEP-4:

4-1. Tick the box as the picture show and then enter the IP address specified in the blank, next to click Add button.

4-2. Then you can see the information about the IP/MAC address on the left side.

--Block MAC address on the list with wrong IP address:

The PC’S MAC address has existed on the rule but with the wrong IP can’t connect to Internet.

--Block MAC address not on the list:

The PC’s MAC address isn’t exists on the rule can’t connect to Internet. 

Application introduction: New version of firmware will be released to improve the various efficiency or to fix some bugs. Following the steps show below so as to realize upgrading.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon         to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2:

Click Advanced Setup->System->Firmware Upgrade on the navigation bar on the left.

STEP-3:

Click Choose File button to select the firmware version and then click Upgrade button. After the router reboots, upgrade is finished.

[ Notice ]

DO NOT power off the device or close the browser window during the upload because it may crash the system.

Application introduction: If you can’t access the router’s setup interface or simply forgot the router’s password, you may reset the current configuration to factory default. There are two ways to. 

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon        to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2:

Click Advanced Setup->System->Config Backup/ Restore on the navigation bar on the left.

STEP-3:

Click Factory Default to reset the router’s configuration.

STEP-4:

Click OK and wait for few seconds to finish resetting. 

Only by one click on the RST/WPS button 

STEP-1:

Press and hold the RST/WPS button for about 10 seconds, until the CPU led blink quickly.

STEP-2:

After nearly 30 seconds, resetting is finished.

Application introduction: AP Client mode allows users with laptop to surf Internet by wireless connection. It’s designed to add wireless function for existed wired Router. 

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon           to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: 

Click Advanced Setup->Wireless->Wireless Mutibridge on the navigation bar on the left.

STEP-3: 

Finished the settings on the page as below, Click Add button after setting.

--Operation: Start

--Wireless Mode: Use Wireless WAN

--SSID: Scan the router’ AP 

--Authentication & Encryption: choose encryption type and enter the password.

STEP-4: 

After click Search AP, it will pop up the page. Choose the AP by double click and then click Select AP button. 

STEP-5: 

Click Advanced Setup->Network->LAN/DHCP Server on the navigation bar on the left.

STEP-6: 

Change the third column of the LAN IP (LAN segment should not be the same with the primary router). Generally, enter 2 if there’s no particular requirement. Then click Apply& Restart button.

STEP-7: 

Wait for 40 seconds, and then it will pop up a window prompts you to reconnect the website as the LAN IP has changed.

STEP-8: 

Login the router’s setting interface, and check the Internet status. 

Application introduction: By port forwarding, the data for Internet applications can pass through the firewall of the router or gateway. This article will show you how to forward ports on your router.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon         to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2:

Click Advanced Setup->NAT/Routing->Port Forwarding on the navigation bar on the left.

STEP-3:

Choose the Rule Type from the drop-down list, and then fill in the blank as below, and then click Add.

--Rule Type: User defined

--Rule Name: Set a name for rule (e.g. toto)

--Protocol: Selectable by TCP, UDP, TCP/ UDP

--External Port: open the external port

--Internal Port: open the internal port 

STEP-4:

After last step, you can see the rule’s information and manage it.

Application introduction:  DDNS (Dynamic Domain Name Server) is to achieve a fixed domain name to dynamic IP resolution .In this way, most users don’t need to use fixed IP and can also name the fixed network system.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon          to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2:

Click Advanced Setup->Ultility->DDNS on the navigation bar on the left.

STEP-3:

Enter the DDNS Service Provider, Host name, User ID and password in the blank space, and then click Add to apply the modification.Finally you can check the DDNS’s status by click Refresh button.

Application introduction:  TOTOLINK routers provide repeater function, which help extending wireless signal easily and expanding the coverage of wireless

Preparation:  Prepare two wireless routers at first, and call the first one AP-1 while the other is AP-2. The router we will setup below is AP-2.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon          to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2:

Click Advanced Setup->Wireless->Wireless Multibridge on the left.

STEP-3:

Click Search AP and find AP-1’s SSID, and then choose the same encryption type and password with AP-1 for AP-2.

Notice: SSID cannot be modified, and password is the same as AP-1 (Encryption and Encryption key)

STEP-4:

Click Advanced Setup->Wireless->LAN/DHCP on the navigation bar on the left.

STEP-5:

Choose Stop to disable DHCP server, and then click Apply button.

STEP-6:

Do next two steps below if AP-1 and AP-2 are both TOTOLINK routers with the same LAN IP.

6-1. Enter the LAN/DHCP interface by click Advanced Setup -> Network ->LAN/DHCP Server on the left.

6-2. Modify the LAN IP of the router to 192.168.X.1 (“x” range from 2 to 254) manually. Then click Apply& Restart button.

Application introduction: With WOL (Wake On Line) function, you can turn on a computer remotely. This document shows you the configuration of WOL on router. 

Notice:

           Please confirm that your network card and system board support Wake ON LAN function at first.

           Before setup WOL, make sure you have opened the remote management function.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon        to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: 

Click Advanced Setup->Utility->WOL on the navigation bar on the left.

STEP-3: 

Click Search MAC address to find the MAC address of the PC.

STEP-4: 

The MAC selected will appear on the column, check the box of Wake Up.

Application introduction: WDS (Wireless Distribution System) provides bridge traffic between two LANs though the air and extends the coverage range of a WLAN. 

Notice:

            Both routers must have the same channel set.

            Both routers must be set to the same band 2.4G or 5G.This article takes 2.4G as an example.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon          to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2:

Click Advanced Setup->Wireless->Wireless Setup on the navigation bar on the left.

STEP-3:

Enter the information show below and then click Apply button for saving modification.

--SSID: Network name (avoid setting the same name with each other)

--Channel: Select by your environment (e.g. 11)

--Encryption: WPA-PSK/WPA2-PSK+AES

--Encryption key: Type in eight to sixty-three letters(a~z) or numbers (0~9)

STEP-4:

Click Advanced setup->Wireless->WDS Setup, then click [AP Scan] to choose  SSID of Secondary Router. 

STEP-1:

Connect your computer to the second router, the first step is the same as the first router.

STEP-2:

Click Advanced setup->Wireless->WDS Setup on the left. 

STEP-3:

Click [AP Scan] and find the SSID of the first router, and then click Add button.The AP’s information will be displayed next as the picture show.

STEP-4:

Enter Wireless Setup interface. Enter the SSID different from the first router, and the same channel、encryption type and password with the first router.  

STEP-5:

Click Advanced Setup->Network->LAN/DHCP Server on the navigation bar on the left.

STEP-6:

Skip to STEP-6 if the router is in the same LAN with Primary Router but different IP Address.

6-1. Change the LAN IP to 192.168.1.X(X must be different from the first one), and then click Apply& Restart button. 

6-2. Login the router’s setting interface again.

STEP-7:

Stop DHCP Service in the LAN/DHCP setup interface by selecting stop as the image show. 

Application introduction: The Remote Management feature allows you to manage the gateway from a remote location, via the Internet. You can use the gateway’s Internet IP Address to enter the router’s setting interface.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon           to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: 

Click Advanced Setup->Firewall->Mgmt Access Control on the navigation bar on the left.

STEP-3: 

Check the box to enable Remote Mgmt port and enter the desired port in the box (default port is 8080), and then click Apply button. 

STEP-4: 

Next to click Use Remote Accesslist and type in the IP allowed if you want to remotely manage by a specify IP address.

STEP-5: 

After that you can enter the setup interface by WAN IP+Remote Mgmt port.

Application introduction: With DHCP server protection function, TOTOLINK routers will detect automatically whether there has other DHCP server and stop assigning IP while there has other DHCP server.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon          to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

Now you can log in the interface to change the router’s SSID. 

STEP-2: 

Click Advanced Setup->Wireless->LAN/DHCP Server on the navigation bar on the left.

STEP-3: 

Select Start to enable DHCP server and tick the box next to DHCP server protection, then click Apply button for saving settings.

Application introduction: Wi-Fi Protected Access (WPA) is the current most secure method of wireless security. You can set one encryption key for your wireless network to prevent occupied by others.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon          to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: 

Click Advanced setup->Wireless->Wireless setup on the navigation bar on the left. 

STEP-3: 

3-1. Click the drop-down list to select WPA-PSK/WPA2-PSK.

3-2. Next to type in Encryption key consist of 8 to 63 letters (a~ z) or numbers (0~ 9). wait for seconds.

Application introduction: Password can ensure your security of your wireless network. Follow these steps if you forgot about it.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon          to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: 

Click Advanced Setup->Wireless->Wireless Setup on the navigation bar on the left.

STEP-3: 

You will see the password in this interface and also you can change it or disable encryption here.

Application introduction: All series routers of TOTOLINK provide E-Mail report function, which can deliver the router’s system status to specific mailbox.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browse

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon         to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: 

Click System->Admin Setup on the navigation bar on the left to enter the admin setup interface.

STEP-3: 

Enter the E-mail of receiver and sender, otherwise, you can use authentication for security. Next to click Apply button for saving settings.

--E-Mail: reciever’s E-Mail.

--Mail Server(SMTP): the server’ s mail

--E-mail for sender: sender’s E-Mail

Application introduction: TOTOLINK routers allow users to save current settings to a file and later you can restore the settings from the file.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon    to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: 

Click Advanced Setup->System->Config Backup/ Restore on the navigation bar on the left.

2-1. Backup Configuration:

Click [Config Backup] and then click save button and browse the location to backup your configuration. 

2-2. Restore Configuration:

Click [Choose File] to select the configuration file, and then click [Config Restore] to restore the configuration.

Application introduction: If you want to access Internet by the Router, please follow the steps below to setup the Internet function.

STEP-1: Connect your computer to the router

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

There are two ways for you to setup Internet functions. You can choose Setup Tool or Internet Wizard to set up.

STEP-2: Select Internet Wizard to setup 

2-1. Please click Internet Wizard icon       to enter the router’s setting interface.

2-2. Please login to the Web Setup interface (the default user name and password is admin).

2-3. You can choose “Automatic Internet Configuration” or “Manual Internet Configuration” in this page. As the WAN port should be connected to the Internet while you select the first one, so we suggest you to choose “Manual Internet Configuration”. Here we take it for example.

2-4. Select one method according to your PC and click next to enter the parameters provided by your ISP.

2-5. The DHCP method is selected by default. Here we take it as an example. You can choose one method to set MAC address according to need. Then click “Next”.

2-6. Click Save and Close button to reply configuration.

STEP-3: Choose Setup Tool to set up

3-1. Please click Setup Tool icon      to enter the router’s setting interface.

3-2. Please login to the Web Setup interface (the default user name and password is admin).

3-3. Select Basic Setup->Internet Setup or Advanced Setup->Network->Internet Setup, there are three modes to choose.

[1] Select DHCP User

If you choose this mode, you will get a dynamic IP address from your ISP automatically. And you will access Internet by using the IP address.

[2] Choose “PPPoE User”

All the users over the Ethernet can share a common connection. If you use ADSL virtual dial-up to connect Internet, please choose this option, you just need to input your User ID and Password.

[3] Choose Static IP User

If your ISP has provided the fixed IP that enable you to access Internet, please choose this option. 

Don’t forget to click “Apply” to make it take effect after you set up.

Application introduction: If you want to modify the router’s user name and password for logging in the web-configuration interface, please follow the steps below.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon       to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

Now you can get to the router’s setting interface to set up.

STEP-2: Modify the user name and password

2-1. Choose Advanced Setup->System->Admin Setup

2-2. Input the new user name and password you want to change

2-3. Just chick “Apply” to make the new user name and password to take effect.

Now you have changed the user name and password, please remember the user name and password for logging in the interface again.

Application introduction: 

Multi-SSID allows users to create network name with different priority for clients or friends accordingly. It is good for access control and your data privacy.

STEP-1:

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon    to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: 

2-1. Click Advanced Setup->Wireless->Multiple BSS on the navigation bar on the left.

STEP-3: 

Fill in the information about SSID in the blank, and then click Add button to apply modification.

--SSID: network name

--SSID Broadcast: Select hidden SSID

--Access Policy:

      a. Allow all: allow users share files or other motion by external network and LAN.

      b. Only for Internet: Only allow users hare files or other motion by external network.

--Encryption：Set encryption key for the wireless network.

STEP-4: 

After adding other SSIDs you can see the information in the Wireless Network Information bar.

Application introduction:

The router’s setting interface allows you to setup basic and advanced settings for better network experience. If you want to login to TOTOLINK router’s setting interface to configure some settings, please follow the steps below.

STEP-1:

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon    to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

STEP-2: Disable SSID broadcast 

2-1. Choose Advanced Setup->Wireless->Wireless Setup.

2-2. Choose “Start” in the Operation bar and uncheck the SSID broadcast bar, then click Apply to make the settings take effect. 

Now you finish the setting to hide SSID, please remember the SSID because when you want to connect to it you should enter the correct SSID for a manual search.

Application introduction:  If you want to alter the SSID of the router, please follow the steps below.

STEP-1: Connect your computer to the router

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon    to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

Now you can log in the interface to change the router’s SSID. 

STEP-2: Alter the SSID of the router

2-1. Choose Advanced Setup->Wireless->Wireless Setup.

2-2. Choose “Start” in the operation bar, and input the new SSID to replace the original SSID (Ex. A2004NS). Then click “Apply” in the lower right corner.

After changing the SSID others can search the new SSID to connect to the Router.

Application introduction: The router’s setting interface allows you to setup basic and advanced settings for better network experience. If you want to login to TOTOLINK router’s setting interface to configure some settings, please follow the steps below.

STEP-1:

1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.

Note: The default IP address of TOTOLINK router is 192.168.1.1, the default Subnet Mask is 255.255.255.0. If you can't log in, Please restore factory settings.

1-2. Please click Setup Tool icon    to enter the router’s setting interface.

1-3. Please login to the Web Setup interface (the default user name and password is admin).

Now you can log in the router’s interface to set up.

STEP-2: 

If don’t want to restore the router to the factory settings, please follow the introduction below.

2-1. Connect your computer to the router by cable or wireless

2-1. Setup you PC to get the IP automatically (Here I take system W10 for example)

[1] Click on   at the bottom right corner on the screen

[2] Click on [Properties] button in the lower left corner

[3] Double click on “Internet Protocol(TCP/IP)”

[4] Select “Obtain an IP address automatically” or Using the following IP Address (The IP address is 192.168.1.xxx (“xxx” range from 2 to 254), the Subnet Mask is 255.255.255.0 and Gateway is 192.168.1.1).

[5] Don’t forget to click “OK” to save the configuration.

3-1. Check the IP address you get automatically in the former step.

The IP address is 192.168.1.8, it means the network segment of your PC is 1, you should enter http://192.168.1.1 into the address bar of your browser.

Enter the router’s setting interface similarly and do some settings.

Both these two repeater methods can help you to expand the wireless coverage and allow more terminals to access Internet. But since Wireless WAN need not stop DHCP Server, all PCs’ IP Addresses are assigned by the Secondary Router itself. So this method allows more PCs to access Internet than Wireless Bridge. In Wireless Bridge mode, the PCs’ permissions to access Internet are decided by Primary Router which can make users to manage the LAN more easily.